Shiva Engineering Works
Home | Site Map | Enquiry | Feedback | Contact Us
Google
corner
Company Profile Services Products Our Clients Contacts Us
corner
Textile Spinning and Weaving Spares
     
 

Category

SPINNING SPARES
steep Autoconer Spares
steep TFO Spares
steep Cone & Cheese Winding
steep Ring Frame Spares
steep Rieter Spares
   
WEAVING SPARES
steep Cimmco Spares
steep Sulzer Spares
steep Dornier Spares
steep Picanol Spares
steep Tsudakoma Airjet Spares
steep Dornier Airjet Spares
steep Picanol Solenoid Valves
steep NP Loom Spares
steep Toyota Airjet Spares
   
WEAVING ACCESSORIES
steep Complete Range of Weaving Accessories
   
LOOMS
(As per Cimmco Design & Standard)
Terry Towel (Automatic)
steep Under Pick
steep Automatic
steep Overpick


special offer

 

 

 

 

 

 


 

Automatic Loom 72"
(As per Cimmco Design & Standard)


Automatic Loom 72"

FRAMING: Built on heavy duty graded casting with all framing members of cast iron to avoid vibration , with double top rail of M.S channel to suit all types dobby mounting, gun metal , sleev for tappet shaft and gun metal bearing for crank shaft provided in the main frame.

DRIVE: Individual drive with cone clutch pulley 3 groove , band brake , crank shaft is forged out of 50 MM tested steel with 3” throw , crank wheel in two parts of 4 DP tooth 36 theeth, v groove pulley provided with gun metal sleeve for longer life, oil dampers of SGI body for absorbing the bang of impact, dagger shaft with carbon steel daggers duly hardended fitted, dagger piece of special steel duly hardended fitted.

SHEDDING: Tappet Shaft of 13/4” DIA of tested steel fitted with 80 degree dwell cam shedding with heald shaft; tappet wheel of 72 teeth of 4 DP stronger teeth.

TAKE UP: Seven Wheel pickles take up motion with machiuned gears: pinions , ratched wheel , twitch roller with left hand and right hand threads to expand the cloth, taking up catch of SG iron, stronger temple bar supported by strong spring, easy sliding on shuttle trap, 3 X10 ring temple , RH box fitted with continous cutter operated by sley.
Spear handle is supplied for stopping the loom.

WARP STOP : Six bank warp stop motion, sliding type, driving lever, link etc are made out of SGI, bridge bars and round bars are plated.

PICKING : Side lever, picking with loose pickers, picking plates are provided with machined serrations for keeping the picking bowl position firm, no chance of slippage, side levers and picking stick are of laminated wood, picking nose are having chilled hard surface and picking bowl of carbon steel hardened for longer life.

LET OFF: Fully positive let off motion, controlling the speed of Beam pipe through beam feeler which regulate the speed of the beam through gears/ levers/ parabola curve cam. Special arrangement of sector brake is provided for mainting the tension of the warp, weight lever shaft wearing provided with nylon liner, beam flange of 24” DIA, back roller 4.5” DIA and easing roller of 3.5” DIA supplied with double easying cams.

BEAT UP: Sley made on one piece angle with 1” thick shisham wood race board and race end of cast iron on both ends, Box front made out of SG iron, with double swell and swell reliving motion for better checking of shuttle, swell bushes are provided of olit (G.M) material to work without oiling, crank arm fitted with hardened bush and sley sword pin, Gun metal bearing on crank shaft end, sley sword etc are of graded casting, reed cap of mild steel for easy Alignment of reed line provided with shuttle guard.

SHUTTLE SIZE: 390X45X34X32X90 DEGREES
PIRN: 190X3 RINGS 27 DIA

FEELING: Side weft fork system is provided in an enclosed Box with MCI weft fork slide, weft fork holder ETC, Shuttle feeler of SG iron TIP is provided.

BATTERY: COP change motion is operated through cam on weft fork hammer, Bobbin disk is provided with nylon clip in place of cast iron, transfer hammer, feed pawl, hold back pawl, bobbin support and latch provided of SGI for longer life.

END CUTTER AND WEFT FEELER: Weft feeler is provide to operate battery on bunch, 5 blade end cutter is provide of improved design of hardened blades to hold and cut the out going weft.

NOTE:

  1. ONE SET OF BEAM PIPE WITH 24” DIA C.I FLANGES SUPPLIED WITH LOOM.
  2. ONE CLOTH ROLLER WILL BE SUPPLIED WITH THE LOOM.
  3. THE LOOMS ARE SUPPLIED WITHOUT WEAVING ACCESSORIES, LOOM DRIVING MOTORS, STARTERS, AND RAILS ETC.

THE FOLLOWING MOTION CAN BE SUPPLIED AT EXTRA COST WITH THE LOOM

  1. CENTRE WEFT FORK MOTION.
  2. SPACER BRACKET TO RAISE TOP RAIL CHANNEL FOR SHAH SIDE DOBBY.
  3. UNIVERSAL MOTION 2X1,2X2,3X1,4X1,WITH ALL PARTS INCLUDING SPRING TOP MOTION MOTION AND SELVEGE MOTION.
  4. LET OFF MOTION OF EXTENDED BRACKET.
  5. ERRECTION GUAGE BOX.

WE CAN MANUFACTURE LOOM ON DEEPER FRAME TO ACCOMMODATE UP TO 16 HEALD FRAME

 
corner   corner
Home | Company Profile | Services | Products | Site Map | Enquiry | Feedback | Contact Us
Copyright 2010, All Right Reserved. Best viewed in 1024x768 screen resolution in IE 5.0 and above. Site By - Graphics World